Відео

Axle kit is unavailable :( I wish I found this sooner

What Axle kit do you recommend since the link says not to buy that one?

Félicitations et merci pour votre excellente vidéo.

🔥🔥🔥🔥🔥

Great job on the rust repair, Scantron! Have you ever tried using a laser cleaner for rust removal? It can be super efficient. Just a thought!

That's a great start for me but my Yamaha rx-1 snowmobile motor doesn't have bolt points for a transmission so I'm looking at using the reduction gearbox bolt points that is behind the flywheel. The output shaft sticks out far so the flywheel will stick out far as well. I'm worried it will put too much pressure on a housing I make out of a cylinder

Set an arc start point a few mm away from your profile to avoid the nick in the edge, which could lead to cracking on a stressed part.

Which brand was it?

Where did u plug into engine with the pressure hose?

Nice, now I can swap my Ford 6.7 to a manual transmission

So just wondering did you have any further diagnosis of the original wiring harness that cause that issue when you dove further in to rewiring. Your method worked on my 2500 silverado but I can't understand all my ground cables are in good condition and connected but when I don't have that jumper wrote I lose all spark on the drivers side of my motor. If my ground cables are good ands I'm not finding a broken wrote what would cause that too happen?

That looks like a solid repair. Did you consider sleeving the new frame rail to the existing section? Probably overkill for this type of truck... 🤔

How thick was the metal? Will it be strong enough for 6.9 c 24v thank

Are you painting it?

This only works if the main shaft is long enough to reach the nose bearing????

Just found your channel, watched a few of your videos so far and this one brought back memories of my military days when we had to get it done with what we had on hand; when you said and I quote "I lack the proper tools to do that; however, I'm cool with coming up with sketchy stuff, so here is my setup".....I busted out laughing (because I can relate) and had to comment, thanks for sharing and great content!

There was a vid similar to this where simply moving the control box on the side of the laser table stopped the hf problem. Might help here Idk.

It's great, but what about to cut 3/8" or maybe 1/2" gauge?

to block the EMF noise try using some ferrite magnet cores around the the wiring that you suspect. Grounding is also key and you could try using foil shielded cabling

Salt huh, that's insane the degree of rust placed on the roads in the USA. It's surprising that the environment plant species can tolerate it too . I do know that less corrosion happens if vehicles ain't parked in a heated garage in winter but left out in the cold instead . Less chemical action at colder temperatures .

Good job.

you need to put that its a paid promotion! I could tell right off the bat it was a sponsored video. I bought one of these from Temu for 4 bucks and they dont work very well at all. Amazon even sells them for $12 please dont try to rip off your subs!

into music is way too loud. js

Vevor will send you a table with 3 legs and want you to send pictures bad customer service save your money build your own

What oil filter did you use me up using I can’t seem to find one that fits for mine

i have a 1999 arctic cat thundercat 1000 motor ( Suzuki-produced, counterbalanced case-reed triple cylinder engine that made 172hp stock). im really thinking about putting in a Mazda Miata . mate it to the car tranny and make the car into a exo car !

I just tried this and oh my God it worked. So many mechanics including myself couldn't figure out how to get spark on that side. So I did what you did in 5 minutes and its running on all cylinders. Thank you so much

That’s awesome and a great build.

In reality, what good is a rear brake? I’m building one for my grandson and I’m thinking I’ll add a front brake. Your opinion would be appreciated. Thanks

Hey, great video, by the way. You make it look simple. You also mentioned that you did a adaptor plate for K swap on a transaxial I am assuming its its for a 944. I am also looking to do this conversion and looking for some information. I hope you can share what you did that would be super helpful. Thanks Michael

You are so inspiring Sir! Audaciously creative. Reminds me of the movie Apollo 13 scene where NASA engineers created CO2 filter out of pile of junks. We need more of this can-do attitude! Bravo~~

Hey man, just been watching some of your videos.. cool stuff! Do you have Instagram or FB?

Thank you so much that was the problem on my son's Cadillac Escalade it was the ground to the block

How are these working out. I need to upgrade and dont have a lot of money

How do you get the spacing between both plates? Do you just hold the engine and trans to where they touch/meet? How do you know what "thickness" of flywheel/clutch to use?? Full video is also confusing

Your channel really deserve more subcriber , my friend...awsome 👍

Nice work, well done

Hello, what program are you using, the one where you put the picture

Wouldn't you need a longer input shaft?

Does it only use AC rods?

Have you tried this on your CNC yet? I’m curious if the high frequency will lead to any EMI/RFI issues.

Can it withstand over head welding Spark ?

You are a beautiful teacher !! Thanks soo much GOD BLESS YOU

I was fully expecting this to be in the xxxx digits in regards to price, but atm it's 80 bucks! That's crazy! Nice video :)

Thank you very much for sharing.😀

Thank you very much for sharing.

But what I wonder is how can the transmission shaft work being it's a 1 1/2 or so back away from the engine now can anyone answer that for me

No way those components are strong enough for suspension, unless you are putting them on a go cart.

Doing all the cutting with a manual trigger. Hell no You are also dragging your torch. Be much better off with a table system with a Z axis and THC.

Can not use a high freq start machine. Change your plasma and you will be all good